服務熱線：手機號碼：19121166298
地 址：上海市北京東路668號科技京城東樓27樓C1室
BALLUFF光電距離傳感器選型
更新時間：2017-05-03 點擊次數：768次
概覽
組件
光電距離傳感器應用示例
插接器與連接導線 光電距離傳感器 適合的固定件
光電距離傳感器能在不同用途中 支持定位、物料流檢查和料位查詢， 包括在較遠距離下。
優勢
它幾乎不受待測目標的材質、顏色及反射度 影響
應用
包裝設備中的尺寸/料位測量或 輪廓識別
木材加工過程中的厚度測量
監測卷筒直徑或垛高 (例如在 印刷機中)
光電距離傳感器 - 貼合您的 要求
Keyfeatures
| Series | Series 63M |
|---|---|
| Design | Block, rotatable connection |
| Connection | Connector, M12x1-S115 |
| Output signal | NPN (2x), NO, 4...20 mA |
| Light source, light type | Laser red light, Laserklasse 2 |
| Ambient temperature | -10...60 °C |
| Working range | 200...6000 mm |
| Resolution | 1.0 mm |
| Switching freq. f max. | 250 Hz |
General attributes
| Basic standard | IEC 60947-5-2, IEC 60947-5-7 |
|---|---|
| Enclosure Type per IEC 60529 | IP67 |
| Protection class | II |
| Short-circuit protected | Yes |
| Protected against polarity reversal | Yes |
| Additional text | The sensor is functional again after the overload has been eliminated. Reference object (target): Gray card, 200 x 200, 90 % remission, axial approach. Full accuracy after warmup phase. Only for NFPA 79 applications (machines with a supply voltage of maximum 600 volts). Device shall be connected only by using any R/C (CYJV2) cord, having suitable ratings. For additional information, refer to user's guide. Order accessories separay. |
| Series | Series 63M |
| Indicator | Error - LED RD Output function - LED YE Ready - LED GN |
| Input function | Emitter on/off |
| Setting | Switching distance Sn |
| Adjuster | Potentiometer 4-turn (2x) |
Electrical attributes
| Rated operating voltage Ue DC | 24,0 V |
|---|---|
| Effective operating current Ie | 200 mA |
| Rated insulation voltage Ui | 75 V DC |
| Electrical version | DC, direct current |
| Hysteresis H max. (in % of Sr) | 0,3 % |
| Load capacitance max. (at Ue) | 0,47 µF |
| Ripple max. (% of Ue) | 15 |
| Switching output | NPN (2x) |
| Switching function | NO |
| Load resistance RL max. | 500 Ohm |
| Turn-off delay toff max. | 2,0 ms |
| Turn-on delay ton max. | 2,0 ms |
| No-load current max. Io at Ue | 75 mA |
| Voltage drop Ud max. (at Ie) | 2,0 V |
| Supplementary output | Error output NPN |
| Switch func. supplementary output | NC |
| Analogue output | Analog I |
| Value range analogue | 4...20 mA |
| Output curve deviation max. | ± 1% of Wh |
| Output characteristic | Linear rising |
| Operating voltage | 15...30 V DC |
Mechanical attributes
| Connector type | M12x1-S115 |
|---|---|
| Oberflächenschutz | Painted |
| Eff. switching distance Sr | 6.000 mm |
| Ambient temperature Ta max. | 60 °C |
| Ambient temperature Ta min. | -10 °C |
| Sensing surface material | Glass |
| Housing material | GD-Al |
| Mounting type | Screw M4 Screw M5 |
| Temperature drift max. | 1.5 mm/K |
| Dist. dev. 18% max. (% of Sr) | 1.5 %, S = 1000..6000 mm |
| Capture range Sd | 200...6000 mm |
| Beam characteristic | Collimated |
| Range Sn | Sn = 6 m, adjustable |
| Minimum operating distance | 200 mm |
| Far working distance Wh | 6000 mm |
| Near working distance Wl | 200 mm |
| Length 1 | 35.0 mm |
| Length 2 | 90 mm |
| Length 3 | 70 mm |
Optical attributes
| Principle of optical operation | Time-of-flight measurement |
|---|---|
| Switching function, optical | Light-on |
| Light spot size, typical | Ø10 mm at 6000 mm |
| Light type | Laser red light |
| Wavelength | 660 nm |
| Ambient light max. | 10,000 Lux |
| Laser class per IEC 60825-1 | 2 |
| Average power Po max. | < 1 mW (IEC 60825-1) |
